Photomicrosensor (Transmissive) EE-SX1107 Be sure to read Precautions on page 25. Dimensions Features Note: All units are in millimeters unless otherwise indicated. * Ultra-compact with a 3.4-mm-wide sensor and a 1-mm-wide slot. * PCB surface mounting type. * High resolution with a 0.15-mm-wide aperture. Absolute Maximum Ratings (Ta = 25C) Item Emitter Optical axis Detector Cross section AA Recommended Soldering Pattern Internal Circuit Ambient temperature Terminal No. Name A Anode K C E Cathode Collector Emitter Unless otherwise specified, the tolerances are 0.15 mm. Symbol Rated value Forward current IF 25 mA (see note 1) Pulse forward current IFP 100 mA (see note 2) Reverse voltage VR 5V Collector-Emitter voltage VCEO 20 V Emitter-Collector voltage VECO 5V Collector current IC 20 mA Collector dissipation PC 75 mW (see note 1) Operating Topr -30C to 85C Storage Tstg -40C to 90C Reflow soldering Tsol 255C (see note 3) Manual soldering Tsol 350C (see note 3) Note: 1. Refer to the temperature rating chart if the ambient temperature exceeds 25C. 2. Duty: 1/100; Pulse width: 0.1 ms 3. Complete soldering within 10 seconds for reflow soldering and within 3 seconds for manual soldering. Electrical and Optical Characteristics (Ta = 25C) Item Emitter Detector Symbol Value Condition Forward voltage VF 1.1 V typ., 1.3 V max. IF = 5 mA Reverse current IR 10 A max. VR = 5 V Peak emission wavelength P 940 nm typ. IF = 20 mA Light current IL 50 A min., 150 A typ., 500 A max. IF = 5 mA, VCE = 5 V Dark current ID 100 nA max. VCE = 10 V, 0 lx Leakage current ILEAK --- --- Collector-Emitter saturated voltage VCE (sat) 0.1 V typ., 0.4 V max. IF = 20 mA, IL = 50 A Peak spectral sensitivity wavelength P 900 nm typ. --- Rising time tr 10 s typ. VCC = 5 V, RL = 1 k, IL = 100 A Falling time tf 10 s typ. VCC = 5 V, RL = 1 k, IL = 100 A 62 EE-SX1107 Photomicrosensor (Transmissive) Engineering Data IF = 5 mA Collector-Emitter voltage VCE (V) Response time tr, tf (s) VCC = 5 V Ta = 25C Load resistance RL (k) Response Time Measurement Circuit Light current IL (A) Sensing Position Characteristics (Typical) IF = 5 mA VCE = 5 V Distance d (mm) VCE = 10 V VCE =2 V Ambient temperature Ta (C) Ambient temperature Ta (C) Relative light current IL (%) Response Time vs. Load Resistance Characteristics (Typical) IF = 5 mA VCE = 5 V Dark current ID (nA) IF = 10 mA Forward current IF (mA) Relative Light Current vs. Ambient Dark Current vs. Ambient TemTemperature Characteristics (Typical) perature Characteristics (Typical) Relative light current IL (%) Light current IL (A) Ta = 25C Ta = 25C VCE = 5 V Forward voltage VF (V) Ambient temperature Ta (C) Light Current vs. Collector-Emitter Voltage Characteristics (Typical) Light Current vs. Forward Current Characteristics (Typical) Sensing Position Characteristics (Typical) Relative light current IL (%) Forward current IF (mA) Forward current IF (mA) Forward Current vs. Forward Voltage Characteristics (Typical) Collector dissipation PC (mW) Forward Current vs. Collector Dissipation Temperature Rating IF = 5 mA VCE = 5 V Distance d (mm) Input Output 90 % 10 % Input Output EE-SX1107 Photomicrosensor (Transmissive) 63 Unit: mm (inch) Tape and Reel Reel 210.8 dia. 3302 dia. 20.5 13 0.5 dia. 801 dia. Product name Quantity Lot number 12.4 +2 0 18.4 max. Tape 1.5 dia. Tape configuration Terminating part (40 mm min.) Pull-out direction Tape quantity 2,500 pcs./reel 64 Leading part (400 mm min.) Parts mounted EE-SX1107 Photomicrosensor (Transmissive) Empty (40 mm min.) Precautions Soldering Information Reflow soldering * The following soldering paste is recommended: Melting temperature: 216 to 220C Composition: Sn 3.5 Ag 0.75 Cu * The recommended thickness of the metal mask for screen printing is between 0.2 and 0.25 mm. * Set the reflow oven so that the temperature profile shown in the following chart is obtained for the upper surface of the product being soldered. Temperature 1 to 5C/s 260C max. 255C max. 230C max. 1 to 5C/s 150 to 180C 120 sec 10 sec max. 40 sec max. Time Manual soldering * * * * Use "Sn 60" (60% tin and 40% lead) or solder with silver content. Use a soldering iron of less than 25 W, and keep the temperature of the iron tip at 350C or below. Solder each point for a maximum of three seconds. After soldering, allow the product to return to room temperature before handling it. Storage To protect the product from the effects of humidity until the package is opened, dry-box storage is recommended. If this is not possible, store the product under the following conditions: Temperature: 10 to 30C Humidity: 60% max. The product is packed in a humidity-proof envelope. Reflow soldering must be done within 48 hours after opening the envelope, during which time the product must be stored under 30C at 80% maximum humidity. If it is necessary to store the product after opening the envelope, use dry-box storage or reseal the envelope. Baking If a product has remained packed in a humidity-proof envelope for six months or more, or if more than 48 hours have lapsed since the envelope was opened, bake the product under the following conditions before use: Reel: 60C for 24 hours or more Bulk: 80C for 4 hours or more EE-SX1107 Photomicrosensor (Transmissive) 65